How to Update INNOVAPRO Electrical Testers

Introduction

Keeping the firmware up to date gives your INNOVAPRO electrical tester better performance, added functions, and support for the latest vehicle systems.

This page shows how to update the firmware from a computer with the Electrical Tester Updater.

Tool Coverage

Tools Tool ID
BA200 Battery Tester Module (0x1001)
BA201 Battery Tester (0x0431)

Download the Electrical Tester Updater

To update your tool, first download and install this application on your computer.

System Requirements:

  • PC: Windows 10 (64-bit editions) / Windows 11
  • Mac: macOS 12.3 – 14.5

Procedure

Step 1: Open the Electrical Tester Updater application.

Make sure your computer is connected to the internet so the application can check for the latest firmware version.

Electrical Tester Updater - Step 1

Step 2: Connect the tool to the computer with the USB Type-C connection. Wait a few seconds for the application to detect the tool.

*Note: Use a USB Type-C data cable

  • Data cables: do both — charge the tool and transfer data. Use a USB Type-C data cable for the update.
  • Charging cables: can only charge the tool, but cannot transfer data. These are commonly called ‘charge-only’ cables.

A charge-only cable cannot transfer data, so the tool may not be detected. If the application does not detect the tool, check the cable first.

Electrical Tester Updater - Step 2

Step 3: Once the tool is detected, the Electrical Tester Updater shows the tool information and, if a new firmware version is available, the Update option. Select Update Now to start the update.

*Note: Already on the latest firmware

If the application shows ‘No updates available’, the tool is up to date. Close the application and disconnect the tool.

Electrical Tester Updater - Step 3

Step 4: The Electrical Tester Updater starts downloading the new firmware version and updating your tool.

*Note: Keep the tool connected

Do not unplug the tool, close the application, or let the computer sleep while the update is running. If the update is interrupted, the application shows the last progress percentage with an update error message — disconnect and reconnect the tool, then start the update again.

Electrical Tester Updater - Step 4

Step 5: The application shows a notification when the update is complete.

Electrical Tester Updater - Step 5

Step 6: Select the Release note button to read the new version information.

Electrical Tester Updater - Step 6

Troubleshooting & FAQs

  • To check for available updates: 
    1. Install and open the Electrical Tester Updater (ETU) on your computer. 
    2. Connect your electrical tester using a USB data cable. 
    3. Follow the instructions displayed in ETU. 
    If a firmware update is available, ETU will notify you and provide instructions to complete the update. 
    Note: Do not disconnect the tester during a firmware update.

  • What should I do if my electrical tester stops working after a firmware update? 
    If your electrical tester stops working after a firmware update, try the following steps: 
    1. Check whether ETU reported that the update completed successfully. 
    2. Check the tester's power supply or battery condition, if applicable. 
    3. Check whether the tester powers on or displays any information. 
    If the tester will not power on, is not recognized by ETU, or does not operate correctly, contact Customer Support. 
    Note: Do not repeatedly attempt firmware updates unless instructed by ETU or Customer Support.

  • If ETU does not detect your electrical tester, try the following steps: 
    1. Make sure the tester is connected directly to your computer using a USB data cable. 
    2. Check that the USB cable supports data transfer, not just charging. 
    3. Try a different USB port or cable. 
    4. Close and reopen ETU, then reconnect the tester. If the issue continues, contact Customer Support for assistance. 
    Note: Avoid using USB hubs or adapters when connecting the tester.

  • If the software update fails, follow these steps: 
    1. Check the error message displayed in the ETU software. 
    2. Make sure your internet connection is stable and the USB cable is properly connected. 
    3. Close and reopen ETU, then reconnect your electrical tester. 
    4. Try updating the tester again. 
    If the issue continues, contact Customer Support for assistance. 
    Note: Do not disconnect the tester or turn off your computer while the update is in progress.

Have Questions?

Please do not hesitate to contact us for assistance.
Our U.S.-based customer service team is ready to assist you.